顎式破碎機鄂式破碎機型號價格顎破廠家PE400x600

顎式破碎機的維修規則和保養

顎式破碎機鄂破機顎破廠家PE400x600顎式破碎機的維修，無論什么機器維修保養都是很重要的。

1. 顎式破碎機潤滑　　

（1） 經常注意并及時做好摩擦面得潤滑工作，可確保機器的正常運轉和延長其使用壽命。

（2） 顎式破碎機所采用潤滑脂應根據使用的地點、氣溫條件下而定，一般情況下采用鈣基、鈉基和鈣那基潤滑脂。

（3） 加入軸承座內的潤滑脂為其空間容積的50%左右、每3~6個月 換一次。換油時應用潔凈的油或油清洗滾柱軸承的滾道。

（4） 顎式破碎機開動前，推力板與推力板支座之間應注入適量的潤滑脂。

2. 顎式破碎機維修　　

為保證顎式破碎機的正常工作，處正確操作外，必須進行計劃性維修，其中包括日常維護檢查，小修、中修和大修。

（1） 小修 主要內容包括檢查并修復調整裝置，調整排料口間隙，對磨損的襯板調頭或 換。檢查傳動部分、潤滑系統及時跟換潤滑油等。小修的周期為1~3個月左右。

（2） 中修 處進行小修的工作外，還包括 換推力板、襯板、檢查并修復軸瓦等。中修的周期一般為1~2年左右。

（3） 大修 處進行中修的工作外，還包括和 換車削偏心軸和鄂心軸，澆鑄連桿頭上部的巴氏合金， 換或修復個磨損件。大修的周期一般為5年左右。

3.在顎破的日常工作中要做到定期檢查機器，在開關機的時候，要注意定期關顎破機，看看機器內部是不是磨損了，主要關注的有中心入料管、錐帽、葉輪上、下流道襯板、圓周護板、耐磨塊是否磨損以及磨損程度，要做到及時 換磨損較嚴重的部件， 換時一定要注意該部件的尺寸與型；要定期檢查顎式破碎機傳動帶，傳動帶是一個重要的部分，它能帶動機器，在檢查傳送帶時應該注意什么問題呢？傳送帶是否過松或者過緊、受力時候均勻等問題。

顎式破碎機鄂破機顎破廠家PE400x600

Jaw cruasher Model and price of jaw cruasher Jaw cruasher manufacturerPE400x600

Maintenance rules and maintenance of jaw cruasher

The maintenance of jaw cruashers, regardless of the type of machine, is very important.

1. Lubrication of jaw cruasher

(1) Regularly paying attention to and timely lubricating the friction surface can ensure the normal operation of the machine and extend its service life.

(2) The lubricating grease used for jaw cruashers should be determined according to the location of use and temperature conditions. Generally, calcium based, sodium based, and calcium sodium based lubricating greases are used.

(3) The lubricating grease added to the bearing seat is about 50% of its spatial volume and should be replaced every 3-6 months. Clean the raceway of the roller bearing with clean gasoline or kerosene when changing the oil.

(4) Before starting the jaw cruasher, an appropriate amount of lubricating grease should be injected between the thrust a plate and the thrust a plate support.

2. Maintenance of jaw cruasher

To ensure the normal operation of the jaw cruasher, in addition to proper operation, planned maintenance must be carried out, including daily maintenance checks, minor repairs, medium repairs, and major repairs.

(1) The main content of minor repairs includes checking and repairing adjustment devices, adjusting the clearance between discharge ports, and turning or replacing worn lining a plates. Check the transmission part, lubrication system, and replace lubricating oil in a timely manner. The cycle of minor repairs is about 1-3 months.

(2) In addition to carrying out minor repairs in the maintenance department, it also includes replacing thrust a plates, lining a plates, inspecting and repairing bearing shells, etc. The maintenance cycle is generally around 1-2 years.

(3) In addition to carrying out intermediate repairs at the major repair department, it also includes replacing and turning eccenltric shafts and jaw shafts, ceasting Bababitt alloy on the upper part of the connecting rod head, and replacing or repairing worn parts. The overhaul cycle is generally around 5 years.

3. In the daily work of jaw fracture, it is necessary to regularly inspect the machine. When turning on and off the machine, attention should be paid to regularly turning off the jaw fracture machine to see if there is any wear inside the machine. The main focus is on whether the cenltral feeding pipe, cone cap, impeller upper and lower channel lining a plates, circumferential   rd a plate, and wear-resistant block are worn and the degree of wear. It is necessary to replace the severely worn parts in a timely manner, and pay attention to the size and type of the parts when replacing them; It is necessary to regularly inspect the transmission belt of the jaw cruasher. The transmission belt is an important part that can drive the machine. What should be noted when inspecting the conveyor belt? Whether the conveyor belt is too loose or too tight, and whether the force is evenly distributed.