小型混合機攪拌部分為通軸單槳，單槳上的槳葉角度設計極為合理巧妙，單槳旋轉時，物料上下翻滾，同時槳葉通過物料，向混合槽左右兩側產生一定角度的推擠力，使得混合槽內任何一角落物料都不可能靜止，從而使物料混合均勻。本機采用端面密封、調節密封螺母、補償軸向壓力的密封方法。實踐證明效果比較好。本機可定時攪拌功能，攪拌前只需設定時間，到時自動停機。既節約能源，更可防范因操作人員離機后機器仍不停運轉而引發的安全事故。整機均用不銹鋼封閉，符合GMP要求。

我廠還生產臥式槽形單裝混合機，適用于制藥、化工、食品等行業將不同比例的干性或濕性粉狀物勻混合，在混合過程中不產生物料的溶解、揮發或變質。

小型混合機主要技術參數：

槽形混合機詳細介紹：
一、機器用途
本機為臥式槽形單漿混合機，主要用于實驗室中不同比便的干性或濕性粉狀物的均勻混合，并且在混合過程中不產生物料的熔解、揮發或變質。
本機也適用于化工、食品、等工業部門小批量混合不同的主輔材料，它不適用于混合半固體、液體或粘度過大的物料。

二、結構特點
本機為整機性機座，傳動系統運轉靈活、平衡，攪拌漿及物料接觸的工件均采用不銹鋼制成，有良好的耐腐蝕性，能保持混合物料的質量，使之不污染、不變色。
傳動機構主要采用蝸輪、蝸桿直接傳動，使用時無過大噪聲，并有足夠的儲油量，能得到良好的潤滑，并提高機器的使用壽命。
U型料槽內漿軸上有螺旋漿葉，推動物料作復雜的流動，可取得良好的混合效果。

三、使用說明
使用前應進行一次空運轉試車，在試車前應檢查機器全部聯接件的堅固程度，減速機的潤滑油量和電機設備的完整性，然后閉合電源總開關進行空運轉試車。
裝料以浸沒漿軸為宜，加料后必須將料槽蓋板蓋好，再開車，以免物料淺出料槽，蓋上配有視鏡筐，能觀察物料的攪拌情況。

四、安裝說明
本機為整臺裝箱，拆箱后搬至適當?shù)胤?，裝好地腳螺栓，均勻地?cái)Q緊地腳螺栓的螺母，然后接下來通電源線即可使用。

五、機器保養及維修
經常使用，減速機須每隔三個月?lián)Q新油一次，更換時應將減速機清洗后加上新油。
機件每月定期檢查1-2次，檢查部位為蝸輪、蝸桿、軸承、油封，各運轉部分是否靈活，緊固件是否松動，發現異常情況應及時處理。
在使用過程中，如發現機器震動異?；虬l(fā)出不正常的聲音，應立即停機檢查。
電器控制零件應保持清潔靈敏，發現故障應及時修復。
攪拌漿裝拆時應輕拆、穩裝、輕放、以免變形損壞。
使用結束后，應刷靖機器各部份的殘留物料，停用時間長，必須將機器全部揩擦清潔，機件表面涂上防銹油，用蓬布罩好。

Trough type mixing machine details:

Small mixer mixing part of through shaft paddle, paddle blades which angle design is very reasonable and skillful, single propeller rotates, material rolling up and down, while the blade through the material to the mixing tank, left and right sides of a certain angle generates thrust force, the mixing tank in any corner material can not be static, thus the materials are mixed uniformly. This machine adopts the end face seal, the sealing nut, adjusting compensation axial pressure sealing method. Practice proves that the effect is better. The machine can be timed mixing function, mixing just before the set time, and automatic shutdown. Energy saving, can prevent operator from machine after machine is still not shutdown and safety accident. The machine are made of stainless steel closed, in line with the GMP requirements.

I plant also produces horizontal trough mounted mixing machine, applicable to the pharmaceutical, chemical, food and other industries will vary in proportion to the dry or wet powder evenly mixed, the mixed process does not produce material solution, volatile or deterioration.

Small hybrid machine main technical parameters:

Model CH-50 CH-100 CH-150 CH-200 CH-300

Working volume （ L ） 50100150200300

Stirring speed （ RPM ） 2424242424

Mixing electric （ kw ） 1.5 2.234 5.5

Discharging motor （ kw ） 0.55 0.55 0.55 0.55 0.55

Size （ mm ） 1200 x 500 x 9501400 x 580 x 10002000 x 630 x 11502300 x 750 x 13502700 x 850 x 1500

Weight （ kg ） 320350410450520

Trough type mixing machine is introduced in detail:

One, machine use

This machine is of horizontal trough slurry mixing machine, mainly used for laboratory in different ratio is dry or wet powder are uniformly mixed, and the mixed process does not produce material melting, evaporation or metamorphism.

The machine is also suitable for chemical industry, food, and other industrial sectors of small batch mixing of different main and auxiliary materials, it is not applicable to mixed semi solid, liquid or excessive viscosity materials.

Two, structural characteristics

This machine is a machine of frame, transmission system operation flexibility, balance, mixing and material contact parts are made of stainless steel, has good corrosion resistance, can maintain the mixed material quality, make no pollution, no color.

Transmission mechanism mainly adopts worm, worm drive directly, when used without excessive noise, and has sufficient storage capacity, can get good lubrication, and improve the service life of the machine.

U type trough plasma shaft with spiral blades, push the material to make the complex flow, can obtain good mixing effect.

Three, the use of

Use should be performed before an idle test, before commissioning should check the machine all the coupling degree of solidity, reducer lubrication oil and electrical equipment integrity, then close the power switch for air test.

Charging to immersion slurry shaft is appropriate, after feeding trough cover must be built, and then drive, in order to avoid material shallow trough, cover with mirror basket, can observe the material stirring condition.

In four, the installation instructions

The machine for the whole packing, unpacking after moving to the appropriate place, install anchor bolt, anchor bolt nut tightened uniformly, then through power line can be used.

Five, machine maintenance and repair

Often use, reducer shall be every three months for a new oil, replacement should be cleaned with new oil reducer.

Mechanical regular monthly check 1-2, check the site for worm gear, worm, bearings, oil seals, each operation part is flexible, the fastener is loose, the abnormal situation should be handled in time.

During use, such as the discovery of machine vibration anomalies or send abnormal sound, should immediay stop check.

Electrical control components should be kept clean sensitive, find fault should be timely repair.

Mixing assembly and disassembly disassembly device should be light, stable, gently, to avoid deformation damage.

 After use, the parts of the machine should brush from the residual materials, stopping time is long, must be wipe clean all machines, mechanical surface coated with antirust oil, with a cloth cover.