當前位置：上海博曼泵業有限公司>>>>S型雙吸離心泵

S型雙吸離心泵

返回列表頁

參考價

面議

具體成交價以合同協議為準

產品型號

品牌

廠商性質經銷商

所在地上海

在線詢價 收藏產品

聯系方式：楊凱查看聯系方式

更新時間：2025-03-10 07:45:27瀏覽次數：185次

聯系我時，請告知來自制藥網

產品分類 品牌分類

暫無信息

上海博曼泵業有限公司

經營模式：經銷商

商鋪產品：32條

所在地區：上海

聯系人：楊凱（銷售經理）

詢價 給他留言

產品簡介

一、概述S型泵系單級、雙吸、泵殼中開的臥式離心泵，供吸送清水或物理化學性質類似于水的其它液體，被吸送液體溫度不超過80℃

詳細介紹

一、概述

S型泵系單級、雙吸、泵殼中開的臥式離心泵，供吸送清水或物理化學性質類似于水的其它液體，被吸送液體溫度不超過80℃。

S型泵主要適用于工廠、礦山、城市給水、電站、水利工程、農田灌溉及排澇等。

型號意義：

二、結構說明

從聯軸器端看，S型泵均為順時針方向旋轉。用戶如需要逆時針方向旋轉的泵，必須在訂貨時特殊提出。

S型泵的主要零部件有：泵體、泵蓋、葉輪、軸、雙吸密封環、軸套、軸承部件與聯軸器部件等。除軸的材料為優質碳鋼外，其余主要零件為鑄鐵制成。

泵殼制成水平中開，泵的吸人口與吐出口均鑄在下半部泵體上，泵蓋以螺尾錐銷定位，與泵體配合。檢查泵殼內部時，只要拆開泵蓋，毋須拆卸進出水管路。泵體的進出水法蘭上，有安裝真空表與壓力表的管螺紋孔。在進出水法蘭的底部有放水用的螺塞。

葉輪經過靜平衡校驗，用軸套與兩側軸套螺母固定在泵軸上，其軸向位置用軸套螺

I. General

Type S pumps are single stage, double suction with horizontally split casings. They are suitable for pumping clean water or liquid similar to it in physical and chemical properties at a temperature not exceeded 80℃.

Type S pumps are. adoptable in factories, mines, water works, power stations, hydraulic engineerings, irrigation or drainage services in agriculture, etc.

The nomenclature of the model is based on its size and characteristic. For example:

II. Construction

Viewed from the driving end, all the S pumps are rotating in clockwise direction. Pumps of counter-clockwise rotation can only be supplied upon special request.

The main components of S pump are listed as follows: lower half casing, upper half casing, impeller, shaft, double suction sealing, shaft sleeves, bearing housings and couplings.

The volute casing is split on the horizontal center line with the suction and dischatge nozzles cast integral with the Pump casing. The upper casing is accurately located on the lower half by the use of dowel pins. It can be removes to inspect the irfterior of the pump without disturbing the pipe connections or pump alignment. The suction and discharge flanges contain tapped holes for vacuum and pressure gauge. At the bottom of the flanges， there are tapped plugs for water drainage.

The impeller has been balanced statically. It is