進口鑄鋼法蘭截止閥

德國巴赫進口鑄鋼法蘭截止閥概述：

進口鑄鋼法蘭截止閥屬于強制密封式閥門，所以在閥門關閉時，必須向閥瓣施加壓力，以強制密封面不泄漏。當介質由閥瓣下方進入閥六時，操作力所需要克服的阻力，是閥桿和填料的磨擦力與由介質的壓力所產生的推力，關閥門的力比開閥門的力大，所以閥桿的直徑要大，否則會發生閥桿頂彎的故障。近年來，從自密封的閥門出現后，法蘭截止閥的介質流向就改由閥瓣上方進入閥腔，這時在介質壓力作用下，關閥門的力小，而開閥門的力大，閥桿的直徑可以相應地減少。同時，在介質作用下，這種形式的閥門也較嚴密。截止閥的流向，一律采用自上而下。
截止閥開啟時，閥瓣的開啟高度，為公稱直徑的25%～30%時，流量已達到zui大，表示閥門已達全開位置。所以截止閥的全開位置，應由閥瓣的行程來決定。本類閥門在管道中一般應當水平安裝。

The definition of imported stainless steel flange valve:

1, stainless steel gate valve structure than simple, easy to manufacture and maintenance.

2, the sealing surface is not easy to wear and abrasion, good sealing, open and close the valve flap and the valve body sealing surface between the relative sliding, so wear and abrasion are not serious, good sealing performance, long service life.

3, open and close, the valve flap stroke is small, so the valve height than the gate valve is small, but the length of the structure than the gate length.

4, opening and closing torque is large, open and close more laborious, open and close time principal.

5, fluid resistance, due to the valve body in the media channel more twists and turns, fluid resistance, power consumption.

6, medium flow direction: nominal pressure PN is less than 16MPa, generally use the media from the valve downstream, under the direction of flow; nominal pressure PN = 20MPa, using reflux, medium from the valve on the downstream direction to increase the seal. When the utility model is used, the valve can only flow in one direction and can not change the flow direction.

7, the valve is fully open when the valve flap is subject to erosion.

進口鑄鋼法蘭截止閥的定義：   

1. 截止閥結構比閘閥簡單，制造與維修都較方便。
   2、密封面不易磨損及擦傷，密封性好，啟閉時閥瓣與閥體密封面之間無相對滑動，因而磨損與擦傷均不嚴重，密封性能好，使用壽命長。
   3、啟閉時，閥瓣行程小，因而截止閥高度比閘閥小，但結構長度比閘閥長。
   4、啟閉力矩大、啟閉較費力，啟閉時間校長。
   5、流體阻力大，因閥體內介質通道較曲折，流體阻力大，動力消耗大。
   6、介質流動方向：公稱壓力PN≤16MPa時，一般采用順流，介質從閥瓣下方向上流；公稱壓力PN≥20MPa時，一般采用逆流，介質從閥瓣上方向下流．以增加密封件能。使用時，截止閥介質只能單方向流動，不能改變流動方向。
   7、截止閥全開時閥瓣經常受沖蝕。
2. The definition of imports valve:
3. 1, the valve structure is simpler than the gate valve, manufacturing and maintenance are more convenient.
4. 2, the sealing surface is not easy to wear and abrasion, good sealing, open and close the valve flap and the valve body sealing surface between the relative sliding, so wear and abrasion are not serious, good sealing performance, long service life.
5. 3, open and close, the valve flap stroke is small, so the valve height than the gate valve is small, but the length of the structure than the gate length.
6. 4, opening and closing torque is large, open and close more laborious, open and close time principal.
7. 5, fluid resistance, due to the valve body in the media channel more twists and turns, fluid resistance, power consumption.
8. 6, medium flow direction: nominal pressure PN is less than 16MPa, generally use the media from the valve downstream, under the direction of flow; nominal pressure PN = 20MPa, using reflux, medium from the valve on the downstream direction to increase the seal. When the utility model is used, the valve can only flow in one direction and can not change the flow direction.
9. 7, the valve is fully open when the valve flap is subject to erosion.

進口鑄鋼法蘭截止閥技術參數：

進口鑄鋼法蘭截止閥guan網：http://www.twvalve。。ｎｅｔ/html/3453.html