Publication 1747-UM011G-EN-P - June 2008
Recommendations for 
Wiring I/O Devices
The following are general recommendations for wiring I/O devices.
•Use acceptable wire gauge. The I/O wiring terminals are 
designed to accept two wires per terminal (maximum) of the 
following size wire:
–Europe:2 mm
2
cross section or smaller
–United States:14 AWG or smaller stranded wires
•See diagram on page 116 for maximum torque values for wiring 
terminal screws and terminal block screws.
•Label wiring to I/O devices, power sources, and ground. Use 
tape, shrink-tubing, or other dependable means for labeling 
purposes. In addition to labeling, use colored insulation to 
identify wiring based on signal characteristics. For example, you 
may use blue for dc I/O wiringand red for ac I/O wiring.
•Route the wires down and away from the module, securing 
them with the cable tie.
•Bundle wiring for each similar I/O device together. If you use 
ducts, allow at least 5 cm (2 in.) between the ducts and the 
controller so there is sufficient room to wire the devices.
•Terminal cover plates have a write-on area for each terminal. 
Use this area to identify your I/O devices. Label the removable 
terminal block if you have not already.
ATTENTION
Before you install and wire I/O devices, disconnect power from 
the controller and any other source to the I/O devices.
ATTENTION
Calculate the maximum possible current in each power and 
common wire. Observe all local electrical codes dictating the 
maximum current allowable for each wire size. Current above 
the maximum ratings may cause wiring to overheat, which can 
cause damage.
Capacitors on input modules have a stored charge that can 
cause a non-lethal shock. Avoid mounting the controller in a 
position where installation or service personnel would be in 
danger from startle reaction.Sidel 4KS-M240/10 伺服驅動器
Sidel 4KS-M240/20 伺服驅動器
Sidel 4KS-M240/30 伺服驅動器
Sidel 4KS-M240/40 伺服驅動器
Sidel 4KS-M240/5 伺服驅動器
Sidel 5000-170/17-B
Sidel 5000-170/25-B
Sidel 5000-170/40-B
Sidel 54K-150/10
Sidel 54K-150/20
Sidel 54K-150/30
Sidel 54K-150/40  
Sidel 54K-240/10
Sidel 54K-240/20
Sidel 54K-240/30
Sidel 54K-240/40
Sidel 54K-P150/80-B 電源
Sidel 54K-P240/80-B 電源
Sidel 55K-240/10
Sidel 55K-240/15
Sidel 55K-240/5
Sidel 56WK-P150/80-B 電源
Sidel 56WK-P150/80-B 電源
Sidel 56WK-P240/80-B 電源
Sidel 56WK-P240/80-B 電源
Sidel 5K-200/10-B
Sidel 5K-200/25-B
Sidel 5K-200/35-B
Sidel 60WKS-CE240/12-PB 伺服驅動器
Sidel 60WKS-CE240/22-PB 伺服驅動器
Sidel 60WKS-CE240/26-PB 伺服驅動器
Sidel 60WKS-CE240/6-PB 伺服驅動器
Sidel 60WKS-M240/12-PB 伺服驅動器
Sidel 60WKS-M240/22-PB 伺服驅動器
Sidel 60WKS-M240/26-PB 伺服驅動器
Sidel 60WKS-M240/3-PB 伺服驅動器
Sidel 60WKS-M240/6-PB 伺服驅動器
Sidel 60WKS-M240/6-PB-24 伺服驅動器
Sidel 60WKS-SPA-ESM
Sidel 60WKS-SPA-ESM
Sidel 60WKS-SPA-ESM
Sidel 64WKS-M240/50-RLG 伺服驅動器
Sidel 64WKS-M240/70 伺服驅動器
Sidel 65WKS-M310/12-PB-0 伺服驅動器
Sidel 65WKS-M310/22-PB-0 伺服驅動器
Sidel 65WKS-M310/26-PB-0 伺服驅動器
Sidel 65WKS-M310/3-PB-0 伺服驅動器
Sidel 65WKS-M310/6-PB-0 伺服驅動器
Sidel 66WKS-M310/35 伺服驅動器
Sidel 66WKS-M310/45 伺服驅動器
Sidel 66WKS-P310/90-B 電源
Sidel 67WKS-M240/3-PB 伺服驅動器
Sidel 67WKS-OPT-B

******1756-OB8EI  1756-OB8EI  1756-OB8EI  ****************************************************

全國zui大的備件庫！---------：張可可
選擇zui有權利的公司！-----：
選擇*的質量！--------
選擇的產品！---------
選擇的服務！------------
選擇zui快的貨期！---------------:
選擇*的價格！------------------:

**************************************************************

Sidel AX2001 Beckhoff 伺服驅動器
Sidel AX2003 Beckhoff 伺服驅動器
Sidel AX2006 Beckhoff 伺服驅動器
Sidel AX2010 Beckhoff 伺服驅動器
Sidel AX2020 Beckhoff 伺服驅動器
Sidel Digifas 7003 伺服驅動器
Sidel Digifas 7100/7200
Sidel Digifas 7103 伺服驅動器
Sidel Digifas 7105 伺服驅動器
Sidel Digifas 7108 伺服驅動器
Sidel Digifas 7112 伺服驅動器