詳細介紹：本廠生產的電動軋蓋機，整機造型新穎、美觀、整機設計合理、輕巧。臺面與防護罩均為不銹鋼材料制造，滾輪強度大，耐磨損，使用壽命長，所軋的瓶鋁蓋密封性好。適合口服液瓶鋁蓋、二毫升瓶鋁蓋、太太口服液瓶鋁塑蓋、噴霧管鋁蓋、青霉素瓶鋁蓋、噴霧管鋁蓋等軋蓋。是全國各大醫院，藥廠、科研等進行批量生產zui為理想的軋蓋設備。
技術參數：
軋蓋速度：24～30瓶/分
電機功率：25W—250W（單機220V）
體積：300×200×350mm
415×180×580mm
重量：8～40kg
電動軋蓋機詳細介紹：
一、上臂的調整
該機可用于軋5-500ml的瓶子蓋，軋不同規格瓶子時，只要把該規格的瓶子放在托盤上，一手托住橫臂，另一只手擰松橫臂左邊的螺母，使橫臂下降或上升，直到軋蓋頭與瓶蓋約20毫米位置時，將螺母擰緊，再用隨機帶的內六角扳手將托環緊靠橫臂后把托環鎖緊。（注）擰緊時注意軋蓋頭與瓶蓋位置對正。
二、V型支塊的調整
將瓶子放入下V型支型內，將支塊上的兩個螺釘旋松，將瓶子和下V型塊一起移動，直到軋蓋頭與瓶蓋位置對正后，將V型塊上的兩個螺釘擰緊。
三、具體操作方法
1、把灌好液體并裝上蓋子的瓶子放到下托盤上，靠在V型支塊上，一手扶住瓶子，另一手將手柄朝后往下拉緊，這時托盤托著瓶子向上抬起，直到瓶蓋與軋蓋頭壓緊。
2、當瓶蓋與軋蓋頭壓緊后，不停地旋轉的三把軋蓋刀頭旋轉數圈后，將瓶蓋軋緊。（注）電機必須順時針運轉。
3、將手柄朝前推，使軋好蓋的蓋子隨著托盤回到原位，整個操作過程完成，以后每軋一個瓶蓋時重復以上的操作即可。
四、軋蓋頭的調整
該機配有多個軋蓋頭，可根據不同瓶子蓋的大小來選擇上軋蓋頭。正式使用前可用瓶子試一下。
1、蓋子軋的不緊，可旋開軋蓋頭鎖緊螺母按逆時針方向旋出上軋蓋頭，然后鎖緊上固定螺母。
2、蓋子軋的太緊，有旋切瓶蓋現象?？尚_上軋蓋頭鎖緊螺母按順時針方向旋進上軋蓋頭，然后鎖緊上固定螺母。
3、瓶蓋下沿收不緊，可根據實際情況適當調小三個軋刀頭的偏心度。如收的太緊，有軋碎瓶子現象，可適當調大三個軋刀頭的偏心度。
Introduced in detail: factory production of electric Capping machine, the novel and beautiful shape, reasonable design, compact. Mesa and the protective cover are made of stainless steel materials, roller strength, wear resistance, long service life, the rolling bottle aluminum cover with good sealing performance. Suitable for oral liquid bottle aluminum cover, aluminum cover two ml bottles, oral liquid bottle cap, the spray tube aluminum cover, aluminum cover, penicillin bottle spray tube aluminum cover, cover rolling. Is the country's major hospitals, pharmaceutical companies, scientific research and production the most ideal cover rolling device.
Technical parameters:
Cover rolling speed: 24 ~ 30 bottles per minute
Motor power: 25W - 250W （ 220V single ）
Size: 300 x 200 x 350mm
415 x 180 x 580mm
Weight: 8～ 40kg
Electric Capping Machine details:
One, the adjusting arm
The machine can be used for rolling 5-500ml bottle cap, rolling bottles of different specifications, as long as the specifications of the bottle is placed on the tray, a support arm, a cross arm on the left hand to loosen the nut, so that the arm drop or rise, capping and cap until ca. 20 mm position, will be nut tightening, and random with the inner six angle wrench will support ring abuts the cross arm after the supporting ring lock. （note ） note with the bottle cap when tightening capping position on it.
In two, V type support block adjustment
The bottle into the V type, the supporting block two screw loosening, bottles and V type block move together, until the capping and cap position on it, V block of two screws.
In three, the specific operation method
1, to fill liquid and the bottle lid fitted into the lower tray, on V type support block, one hand holding the bottle, on the other hand will handle back down tight, then the tray of a bottle up, until the bottle cap and the capping presses.
In 2, when the cap and capping after pressing, spinning three cover rolling cutter head rotation after a few laps, the bottle cap can be tightly rolling. （note ） motor must run clockwise.
In 3, the handle forward push, make rolling cover lid with the tray back in situ, the whole operation process is completed, each one a bottle of repeat the above operation.
In four, capping adjustment
The machine is equipped with a plurality of capping, according to different bottle cover size selection on capping. Before using the available bottles to try.
1, cover rolling is not tight, loosen the capping nut lock anti-clockwise rotation on capping, and then lock fixing nut.
2, cover rolling too tight, peeling cap phenomenon. Loosen the lock nut on the capping clockwise rotation in the capping, and then lock fixing nut.
In 3, the bottle cap along not tight, according to the actual situation of the appropriate regulating mistress a rolling cutter eccentricity. Such as receiving tight, a crushing bottle phenomenon, can be appropriate three rolling cutter eccentricity.
彭州市|
满城县|
济南市|
凤庆县|
肇州县|
邹城市|
安顺市|
建始县|
永寿县|
平谷区|
交口县|
朝阳县|
屏东县|
龙山县|
丰顺县|
正安县|
江山市|
容城县|
海南省|
沅陵县|
玉林市|
郧西县|
清丰县|
新余市|
凌海市|
邢台县|
措美县|
五大连池市|
黄山市|
龙陵县|
怀仁县|
蒙阴县|
扬中市|
曲靖市|
峨边|
富宁县|
包头市|
松溪县|
鹤庆县|
出国|
明光市|