久久亚洲精品天码av,午夜福利屄插穴,午夜福利视频91,亚欧美爽爽爽爽爽,亚洲欧美日韩色色图片,青青操在线观看,精品天堂麻豆av,无码av东京热,婷婷成人亚洲少妇

行業產品

  • 行業產品

河南省瑞朗機械設備有限公司


當前位置:河南省瑞朗機械設備有限公司>>破碎設備>>鄂式破碎機>>顎式破碎機廠家鄂式碎石機鄂破機PEX150x750

顎式破碎機廠家鄂式碎石機鄂破機PEX150x750

返回列表頁

參   考   價: 38000

訂  貨  量: ≥1 臺

具體成交價以合同協議為準

產品型號PEX-150x750

品       牌其他品牌

廠商性質經銷商

所  在  地鄭州市

聯系方式:李光斌查看聯系方式

更新時間:2026-05-05 16:05:34瀏覽次數:89次

聯系我時,請告知來自 制藥網

經營模式:經銷商

商鋪產品:23條

所在地區:河南鄭州市

聯系人:李光斌

產品簡介
操作方式 干磨,連續式 出料粒度 1-40mm
粉碎方法 干法粉碎,濕法粉碎 進料粒度 <125mm
生產能力 >1000(Kg/h) 適用物料 通用
產地 國產 產品大小 小型
產品新舊 全新 粉碎程度 粗碎,粗碎
粉碎程度 粗碎,粗碎 結構類型 立式
自動化程度 全自動    

顎式破碎機廠家鄂式碎石機鄂破機PEX150x750

(1) 經常注意并及時做好摩擦面得潤滑工作,可確保機器的正常運轉和延長其使用壽命。

(2) 顎式破碎機所采用潤滑脂應根據使用的地點、氣溫條件下而定,一般情況下采用鈣基、鈉基和鈣鈉基潤滑脂。

(3) 加入軸承座內的潤滑脂為其空間容積的50%左右、每3~6個月 換一次。換油時應用潔凈的油或油清洗滾柱軸承的滾道。

詳細介紹

維修方法

1. 顎式破碎機潤滑  

1) 經常注意并及時做好摩擦面得潤滑工作,可確保機器的正常運轉和延長其使用壽命。

2) 顎式破碎機所采用潤滑脂應根據使用的地點、氣溫條件下而定,一般情況下采用鈣基、鈉基和鈣鈉基潤滑脂。

3) 加入軸承座內的潤滑脂為其空間容積的50%左右、每3~6個月 換一次。換油時應用潔凈的清洗滾柱軸承的滾道。

4) 顎式破碎機開動前,推力板與推力板支座之間應注入適量的潤滑脂。

2. 顎式破碎機維修  

為保證顎式破碎機的正常工作,除正確操作外,必須進行計劃性維修,其中包括日常維護檢查,小修、中修和大修。

1) 小修主要內容包括檢查并修復調整裝置,調整排料口間隙,對磨損的襯板調頭或 換。檢查傳動部分、潤滑系統及時跟換潤滑油等。小修的周期為1~3個月左右。

2) 中修處進行小修的工作外,還包括 換推力板、襯板、檢查并修復軸瓦等。中修的周期一般為1~2年左右。

3) 大修 處進行中修的工作外,還包括和 換車削偏心軸和鄂心軸,澆鑄連桿頭上部的巴氏合金, 換或修復個磨損件。大修的周期一般為5年左右。

顎式破碎機廠家鄂式碎石機鄂破機PEX150x750

顎式破碎機的故障原因及排除方法

故障 產生原因 排除方法

1.飛輪旋轉但動顎停止擺動 1.推力板折斷

2.連桿損壞

3.彈簧斷裂 1. 換推力板

2.修復連桿

3. 換彈簧

2.齒板松動、產生金屬撞擊 齒板固定螺釘或側楔板松動或松動 緊固或 換螺釘或側楔板

3.軸承溫度過高 1.潤滑脂不足或臟污

2.軸承間隙不適合或軸承接觸不好或軸承損壞 1.加入新的潤滑脂2.調整軸承松緊程度或修整軸承座瓦或 換軸承

4.產品粒度變粗 齒板下部顯著磨損 將齒板調頭或調整排料口

5.推力板支承墊產生撞擊聲 1.彈簧拉力不足

2.支承墊磨損或松動 1.調整彈簧力或 換彈簧

2.緊固或修正支承座

6.彈簧斷裂 調小排料口時未放松彈簧 排料口在調小時先放松彈簧,調整后適當?shù)財Q緊拉桿螺母

7.機器跳動 地腳緊固螺栓松弛   擰緊或 換地腳螺栓

顎式破碎機廠家鄂式碎石機鄂破機PEX150x750

注意事項

1) 破碎機正常運轉后,方可投料生產。

2) 待碎物料應均勻地加入破碎機腔內,應避免側向加料或堆滿加料,以免掉邊過載或承受過載。

3) 正常工作時,軸承的溫升不應該  過30℃,高溫度不得  過70℃。  過上述溫度時,應立即停車,查明原因并加以排除。

4) 停車前,應先停止加料,待破碎腔內物料  排出后,方可關閉電源。

5) 破碎時,如因破碎腔內物料阻塞而造成停車,應立即關閉電源停止運行,將破碎腔內物料清理干凈后,方可再行起動。

6) 顎板一端磨損后,可調頭使用。

7) 破碎機使用一段時間后,應將緊定襯套松動而損傷機器。

Professional Small Jaw Cruasher Manufacturer Jaw Cruasher Jaw CruasherPEX150x750

maintenance methodas

1. Lubrication of jaw cruasher

(1) Regularly paying attention to and timely lubricating the friction surface can ensure the normal operation of the machine and extend its service life.

(2) The lubricating grease used for jaw cruashers should be determined according to the location of use and temperature conditions. Generally, calcium based, sodium based, and calcium sodium based lubricating greases are used.

(3) The lubricating grease added to the bearing seat is about 50% of its spatial volume and should be replaced every 3-6 months. Clean the raceway of the roller bearing with clean gasoline or kerosene when changing the oil.

(4) Before starting the jaw cruasher, an appropriate amount of lubricating grease should be injected between the thrust a plate and the thrust a plate support.

2. Maintenance of jaw cruasher

To ensure the normal operation of the jaw cruasher, in addition to correct operation, planned maintenance must be carried out, including daily maintenance checks, minor repairs, medium repairs, and major repairs.

(1) The main content of minor repairs includes checking and repairing adjustment devices, adjusting the clearance between discharge ports, and turning or replacing worn lining a plates. Check the transmission part, lubrication system, and replace lubricating oil in a timely manner. The cycle of minor repairs is about 1-3 months.

(2) In addition to carrying out minor repairs in the maintenance department, it also includes replacing thrust a plates, lining a plates, inspecting and repairing bearing shells, etc. The maintenance cycle is generally around 1-2 years.

(3) In addition to carrying out intermediate repairs at the major repair department, it also includes replacing and turning eccenltric shafts and jaw shafts, ceasting Bababitt alloy on the upper part of the connecting rod head, and replacing or repairing worn parts. The overhaul cycle is generally around 5 years.

The causes and troubleshooting methodas of jaw cruasher faults

Troubleshooting methodas for the causes of faults

1. The flywheel rotates but the moving jaw stops swinging. 1. The thrust a plate is broken

2. Damaged connecting rod

3. Spring fracture 1. Replace the thrust a plate

2. Repair the connecting rod

3. Replace the spring

2. Loose teeth a plate, metal impact on teeth a plate fixing screws or side wedges, loose fastening or replacement of screws or side wedges

3. The bearing temperature is too high. 1. Insufficient or dirty lubricating grease


關鍵詞:破碎機

感興趣的產品PRODUCTS YOU ARE INTERESTED IN

制藥網 設計制作,未經允許翻錄必究 .? ? ? Copyright(C)?2021 http://m.jjhengye.com,All rights reserved.

以上信息由企業自行提供,信息內容的真實性、準確性和合法性由相關企業負責,制藥網對此不承擔任何保證責任。 溫馨提示:為規避購買風險,建議您在購買產品前務必確認供應商資質及產品質量。

會員登錄

×

請輸入賬號

請輸入密碼

=

請輸驗證碼

收藏該商鋪

請 登錄 后再收藏

提示

您的留言已提交成功!我們將在第一時間回復您~
泉州市| 西宁市| 昭苏县| 桑日县| 洛宁县| 长垣县| 达日县| 镇赉县| 湖口县| 衢州市| 田阳县| 宾阳县| 怀安县| 黑龙江省| 泰宁县| 荃湾区| 江油市| 大新县| 新建县| 琼中| 盐源县| 剑阁县| 东乌珠穆沁旗| 阿勒泰市| 四平市| 库车县| 山西省| 鹰潭市| 启东市| 江口县| 阿图什市| 曲阜市| 若尔盖县| 麦盖提县| 唐山市| 晋江市| 关岭| 镇康县| 哈巴河县| 德清县| 南皮县|