當前位置：山東凱拓自控技術有限公司>>西門子原裝傳感器>>西門子室外溫度傳感器QAC31

西門子室外溫度傳感器QAC31

返回列表頁

參考價

面議

具體成交價以合同協議為準

產品型號

品牌

廠商性質代理商

所在地

在線詢價收藏產品

聯系方式：袁啟磊查看聯系方式

更新時間：2025-06-16 15:08:51瀏覽次數：363次

聯系我時，請告知來自制藥網

產品分類 品牌分類

暫無信息

山東凱拓自控技術有限公司

經營模式：代理商

商鋪產品：22條

所在地區：山東濟南市

聯系人：袁啟磊（銷售）

詢價 給他留言

產品簡介

SIEMENSSymaro™OutsideTemperatureSensors?Activesensorsforacquiringtheoutsidetemperature?OperatingvoltageAC24VorDC13

詳細介紹

SIEMENS

Symaro™
Outside Temperature Sensors
? Active sensors for acquiring the outside temperature
? Operating voltage AC 24 V or DC 13.5...35 V
? Signal output DC 0...10 V or 4...20 mA
Use
The QAC31... outside temperature sensors are for use in heating, ventilation and air conditioning plants as:
? Reference sensors for outside temperature-compensated control
? Measuring sensors, e.g. for optimization, measured value indication, or for connection to a building automation and control system
? High-end sensors for acquiring the room temperature in commercial spaces
Type summary

Type reference	Measuring range	Operating voltage	Output signal
QAC3161	-50...+50 °C	AC 24 V+20%/DC 13.5...35 V	DC 0...10 V
QAC3171	-50...+50 °C	DC 13.5...35 V	4...20 mA

Ordering and delivery
When ordering, please give name and type reference, e.g.:
Outside temperature sensor QAC3161.
The sensor is supplied complete with cable entry glａnd M16.
Siemens Building Technologies
HVAC Products

Equipment combinations

All systems or devices capable of acquiring and handling the sensor's DC 0...10 V or 4...20 mA output signal.

The sensor acquires the outside temperature via its sensing element whose resistance value changes as a function of the temperature. This change is converted to a DC 0...10 V or 4...20 mA output signal, depending on the type of sensor. The output signal corresponds to the selected temperature range.

The outside temperature sensor consists of housing, printed circuit board, connection terminals and measuring probe.
The two-sectional housing is comprised of base and removable cover (screwed connection). The measuring circuit and the setting element are located on the printed circuit board inside the cover, the connection terminals on the base.
The measuring probe is screwed into the bottom of the housing.
Cable entry is either from the rear (concealed wiring) or from below (surface-run wires). For that purpose, a hole can be knocked out in the base or the enclosed cable entry glａnd M16 can be screwed into the bottom of the base.

The setting element is located inside the cover. It consists of 6 pins and a shorting plug. It is used to select the required measuring range and to activate the test function.

The different plug positions have the following meaning
? For the temperature measuring range:
Shorting plug in the left position (R1) = 0...50 °C
Shorting plug in the mid position (R2) = -50...+50 °C (factory setting)
Shorting plug in the right position (R3) = -35...+35 °C
? For activating the test function:
Shorting plug in the horizontal position: The values according to the table "Test function active" will be made available at the signal output.
In the event of fault, the output signal will reach 0 V (4 mA) after 60 seconds.

To power the sensor, a transformer for safety extra low-voltage (SELV) with separate windings for 100 % duty is required. When sizing and electrically protecting the transformer, local safety regulations must be observed.

When sizing the transformer, the power consumption of the outside temperature sensor must be taken into consideration. For correct wiring, refer to the Data Sheets of the devices with which the sensor is used.
The permissible cable lengths must be observed.

When laying the cables, it must be observed that the longer the cables run side by side and the smaller the distance between them, the greater the electrical interference. Twisted pair cables are required for the secondary supply lines and the signal lines.

Mounting location	Depending on use, the outside temperature sensor must be located as follows: ? For control: On the wall of the house or building that has the windows of the occupied rooms, but the sensor must not be exposed to the morning sun. In case of doubt, it should be mounted on the wall facing north or north-west ? For optimization: Always on the coldest wall of the house or building (normally the wall facing north). The sensor must never be exposed to the morning sun
Mounting height	Preferably in the middle of the house or building or heating zone, but at least 2.5 m above the ground. The sensor must not be fitted at the following locations: ? Above windows, doors, air exhausts or other heat sources ? Below balconies or the eave of the roof To prevent measuring errors due to air circulation, the cable conduit at the sensor should be sealed. The sensor may not be painted over. Mounting Instructions are printed on the packaging.
Commissioning notes	Check wiring before switching on power. The temperature measuring range must be selected on the sensor, if required.

Mounting notes

Technical data

Environmental conditions	Operation Climatic conditions Temperature (housing with electronics) Humidity Mechanical conditions	IEC 721-3-3 class 3K5 -40...+70 °C 5...95 % r. h. (non-condensing) class 3M2
	Transport Climatic conditions Temperature Humidity Mechanical conditions	IEC 721-3-2 class 2K3 -25...+70 °C <95 % r. h. class 2M2
Materials and colors	Base	polycarbonate, RAL 7001 (silver-grey)
	Cover	polycarbonate, RAL 7035 (light-grey)
	Measuring nipple	stainless steel 1.4401
	Cable entry gland	PA, RAL 7035 (light-grey)
	Sensor (complete assembly)	silicone-free
	Packaging	corrugated cardboard
Standards	Product safety Automatic electrical controls for household and similar use	EN 60 730-1
	Electromagnetic compatibility Immunity Emissions	EN 61 000-6-2 EN 61 000-6-3
	C€ conformity to	EMC Directive 89/336/EEC
	G conformity to Australian EMC Framework Radio Interference Emission Standard	Radio Communication Act 1992 AS/NZS 3548
Weight	Incl. packaging QAC3161 QAC3171	approx. 0.13 kg approx. 0.13 kg