ZR01A01-10氧化鋯鋯池日本橫河 Many industries use a variety of fuel sources to fire their processes, including natural gas, coal, oil, trash and waste (also known as biomass). Coal and biomass fuels release a s......
ZR01A01-10氧化鋯鋯池——日本橫河
Many industries use a variety of fuel sources to fire their processes, including natural gas, coal, oil, trash and waste (also known as biomass). Coal and biomass fuels release a significant amount of carbon particulate when burned, known as fly ash. This fly-ash can clog the Zirconia cell, resulting in slow or no response to changes in the oxygen concentration.
Self Cleaning Fly-Ash Filter (M1234SE-A)
The Self Cleaning Fly-Ash Filter (M1234SE-A) is a sintered filter that incorporates an aerodynamic shield that deflects the particles, and prevents fly-ash build up from clogging the ZR22 Oxygen Probe. This filter should be used whenever coal or biomass is the primary fuel source.
• Filter Material: Hastelloy X
• Base Material: 316 SS
• Max. O.D.: 6.35cm (2.5in)
• Max Operating temp: 700?C (1292?F)
• Pore size: 10 micron
Standard installation of the Self Cleaning Fly-Ash Filter (M1234SE-A)
*Note: Prior to installation, clean the ZR22G Detector end with a wire brush to remove existing ash or dust.
1. Slide the closed end of the filter shield over the end of the probe approximately 9 inches.
2. Slide the filter element over the detector and into the space between the detector and the shield approximately 8 inches. This may be a snug fit, and might require a firm push; however, the filter should not be forced onto the detector.
3. Slide the end of the shield over the filter.
4. Align the shield so it protects the filter element from direct gas flow. The shield should cover the filter, and be flush with the closed end of the filter, as shown:
*NOTE: When using the M1234SE-A Self Cleaning Fly-Ash Filter in conjunction with the ZR22R Probe Protector, repeat the steps above, but invert the M1234SE-A shield away from the direction of flow.
5. Tighten the clamp screw until the filter cannot be moved by hand. THE SCREW SHOULD NOT BE TIGHTENED BEYOND THIS POINT. Over tightening the assembly can damage the detector and filter.
Dust and Oil Filter E7042UQ
50.8mm (2 in)
The Dust and Oil Filter attaches to the end of the ZR22 Oxygen Probe, and is used for oil fired applications as well as black liquor recovery systems. The Filter (E7042UQ) utilizes a Silicon Carbide (SiC) filter disc enclosed in a 316SUS cylinder. Once installed the filter will have the same outside diameter as the ZR22 Oxygen Probe (as shown).
Dust and Oil Filter Installation (E7042UQ)
1. Remove the bolts, washers, plate, calibration tube and filter screen that hold the Zirconia
cell in place.
2. Remove the Zirconia cell and metal o-ring. Ensure that when removing the Zirconia cell,
it is rotated in the direction etched on the face of the cell. (Should be clockwise). Failure
to do so may damage the contact spring.
3. Do not re-use the metal o-ring. The dust and oil filter comes with a new metal o-ring that
should be used. Replace Zirconia cell (ensuring that the cell is rotated clockwise as it is
inserted), plate, calibration tube, and filter screen.
4. Align the notch on the E7042UQ Dust and Oil Filter with the calibration tube. 5. Apply anti-seize compound to the bolt threads. Insert the bolts, and torque to 51 in/lbs. The E7042UQ Dust and Oil Filter installation is now complete, and the ZR22 Oxygen Probe can be installed.
采購中心
德令哈市|
吕梁市|
龙陵县|
大方县|
塔河县|
松阳县|
修水县|
永兴县|
武夷山市|
隆昌县|
湖南省|
太谷县|
水城县|
郎溪县|
墨竹工卡县|
岳普湖县|
台中县|
玉林市|
永寿县|
油尖旺区|
孝昌县|
宣化县|
多伦县|
陈巴尔虎旗|
玉龙|
聊城市|
津市市|
双桥区|
都江堰市|
蓬莱市|
宁国市|
溆浦县|
禹州市|
福鼎市|
天全县|
绍兴县|
栖霞市|
祁连县|
汉中市|
宣恩县|
西和县|
用戶評(píng)論
發(fā)布評(píng)論